Products

Gear Pump

Welcome to Apple Hydraulic of Hydraulic Pump. In this category you will find all manner of Hydraulic Gear Pumps, Hydraulic Vane Pumps, and Hydraulic Piston Pumps of various sizes. Fixed and variable displacements, pressure compensated, load sense, hydraulic transmission pumps and double pumps from different manufacturers, and all at incredible prices to suit a variety of applications.

Read more

Bell Housing

By using bell housings motor and pump shaft are aligned to each other optimally

Material: cast iron - higher resistance compared to aluminium

Applicable in mining and offshore

Good noise damping features

Horizontal assemby in connection with KTR foot flanges possible

On request bell housing available with ventilation and leak oil bore

Read more

Direct Acting Relief Valve

Pressure Relief valves are used to limit the pressure in the system as set on the valve. Direct Relief Valves are applicable in systems where quick pressure release is of prime concern for safety. This is an economical solution for systems having moderately large flows. The valve is a zero leak valve due to the metal sealing of the poppet on the seat.

Read more

Directional Control Valve

A valve is a device that receives an external signal (mechanical, fluid pilot signal, electrical or electronics) to release, stop or redirect the fluid that flows through it. The function of a DCV is to control the direction of fluid flow in any hydraulic system. A DCV does this by changing the position of internal movable parts. To be more specific, a DCV is mainly required for the following purposes: To start, stop, accelerate, decelerate and change the direction of motion of a hydraulic actuator. To permit the free flow from the pump to the reservoir at low pressure when the pump’s delivery is not needed into the system. To vent the relief valve by either electrical or mechanical control. To isolate certain branch of a circuit.

Read more

Flow Control Valve

Flow Control Valves that are hydraulically operated and throttled to maintain a preset flow rate and/or limit the maximum flow rate regardless of changing upstream and downstream pressures. The throttled position of the main valve is controlled by an adjustable pilot valve which senses pressure across an orifice plate.Flow Control Valves that are hydraulically operated and throttled to maintain a preset flow rate and/or limit the maximum flow rate regardless of changing upstream and downstream pressures. The throttled position of the main valve is controlled by an adjustable pilot valve which senses pressure across an orifice plate.

Read more

Fluid Level Indicators

Fluid level indicators are used to provide a means to view the level of fluid in a container or tank. Offered in a variety of combinations of metal, plastic and glass, to accommodate different types of fluids and tank pressure. This section also includes threaded plugs, pipe plugs, drain plugs and filler breathers. These components are designed to be used to seal a variety of openings and are offered in both metal and plastic. Types include magnetic (to filter out metal filings), versions with fill or drain labels, dipsticks, splash guards, and strainers.

Read more

Gauge Isolator Valve

For the diverse requirements of our clients we are involved in offering an extensive range of Gauge Isolator Valve. Our gauge isolator valves are very durable and highly efficient to use for with its compact design that enable easy gauge positioning and eliminate the need for supporting brackets. Additionally, these gauge isolator valves have seat type valves which are sturdy and long lasting.

Read more

Hydraulic Cylinders

With our competence in hydraulic system solutions, we can cover a wide range of products in hydromechanical engineering. One focus area is the design, production and commissioning of hydraulic cylinders with diameters up to 720 mm and strokes up to 20 m used in spillway radial gates, sluice gates, intake gates, bypass gates etc.

Read more

Hydraulic Mani Fold Block

At HydraForce we believe that better performance comes from working together, and our engineers and field representatives will work with you to design your hydraulic control system. We understand that optimizing the performance of your machine starts with creative hydraulic integrated circuits, and when you work with HydraForce, you can select from the broadest product range in the industry.

Read more

Hydraulic Power Pack

The function of Hydraulic Power is to simply convert a primary drive source into a hydraulic fluid flow.

Read more

Mobile Control Valve

The Hydraulic Mobile Control Valves are used as essential components of various equipment used in construction field, agricultural arena and power distribution plants. As a growth oriented  manufacturer and exporter, we are offering premium quality Hydraulic Mobile Control Valves  that have attained popularity for their long functional life, unique sealing properties, application specific design, superior finishing, pressure bearing capacity and availability in different specifications. These have been developed by using nest grade carbon steel or alloy steel with rust protection capacity.

Read more

Needle Valve

Needle valves have a slender, tapered point at the end of the valve stem that is lowered through the seat to restrict or block flow. Fluid flowing through the Needle valve turns 90 degrees and passes through an orifice that is the seat for a rod with a cone shaped tip. Needle valves are widely used to accurately regulate the flow of liquids and gases at low flow rates. The fine threading of the stem and the large seat area allow for precise resistance to flow.

Read more

Pilot Operated Check Valve

1.5 Pilot-Operated check Valve A pilot-operated valve along with its symbol is shown in Fig. 1.4. This type of check valve always permits free flow in one direction but permits flow in the normally blocked opposite direction only if the pilot pressure is applied at the pilot pressure point of the valve. The check valve poppet has the pilot piston attached to the threaded poppet stem by a nut. The light spring holds the poppet seated in a no-flow condition by pushing against the pilot piston.

Read more

Pressure Relief Valve

The relief valve (RV) is a type of valve used to control or limit the pressure in a system or vessel which can build up for a process upset, instrument or equipment failure, or fire. The pressure is relieved by allowing the pressurised fluid to flow from an auxiliary passage out of the system.

Read more

Suction Strainer

These screens can be used for oil, chemicals and water (they will not rust). They are made of tough glass-filled nylon and stainless steel, and mount on 3/8 to 3 inch threaded pipe. Choose from 4 to 200-mesh wire cloth.

Read more

Tank Filler Breather

To strain fluids being added to tanks and to filter entering air. These units are offered for top or side mounting, with choice of neck height, basket depth, inner guards, dipsticks and magnets. In all-metal, all-stainless, or all-nylon construction.

Read more

Hydraulic Radial Piston Motor

If you are looking to source a radial piston motor, Hydraulics Online has widespread, competitive access to both leading and niche hydraulic motor manufacturers from around the world and can supply you with a wide range of radial piston motors including: compact radial piston motors, dual displacement radial piston motors, fixed displacement radial piston motors, low speed high torque radial piston motors, two speed radial piston motors and variable displacement radial piston motors. We are also able to offer a repair and refurbishment service on most brands of radial piston motor. We are Dealing In Replacement of Hydraulic Radial Piston Motor : Zihyd Hydraulic Radial Piston Motor JMDG Series, Sai Hydraulic Radial Piston Motor, Intermot Hydraulic Radial Piston Motor, Kawasaki Hydraulic radial Piston Motor, Bignozzi Hydraulic Radial Piston Motor,Bosch Rexroth Hydraulic Radial Piston Motor.

Read more

Hydraulic Gear Coupling

The Apple Hydraulic Flexible Drive Coupling consists of two gear hubs engaging in a sleeve of high grade plastic material. Has superior strength and a wide operating temperature range. The gears have crowned-tooth form which permit axial and angular misalignment. The couplings have undergone extensive testing under severe load conditions. They are easy to assemble and require no maintenance or lubrication and do not emit transmission noise. Available in non-corrosive options of Stainless Steel and Nylon materials also

Read more

Hydraulic Fittings

The Apple Hydraulic Flexible Drive Coupling consists of two gear hubs engaging in a sleeve of high grade plastic material. Has superior strength and a wide operating temperature range. The gears have crowned-tooth form which permit axial and angular misalignment. The couplings have undergone extensive testing under severe load conditions. They are easy to assemble and require no maintenance or lubrication and do not emit transmission noise. Available in non-corrosive options of Stainless Steel and Nylon materials also

Read more

Hydraulic Ball Valve

Apple Hydraulic Development has been dedicating to hydraulic ball valve and stainless steel ball valves for Standard Quality . We consistently focus on severe processing of products by stringent testing, quality planning, zero leakage guarantees. Hydraulic ball valves, stainless steel ball valves that we manufactured are exported over more countries in the world

Read more

Hydraulic Check Valve

A hydraulic valve properly directs the flow of a liquid medium, usually oil, through your hydraulic system. The direction of the oil flow is determined by the position of a spool. A hydraulic system can only function - as per requirements - by using valves. Thus, you should always look for the correct type of hydraulic valve to serve your intended purpose.

Hydraulic valves are available in a variety of sizes. The size required is determined by the maximum flow of the hydraulic system through the valve and the maximum pressure in the hydraulic system. Hydraulic valves are available with different mountings: e.g. mounting in pipe lines, threaded connection as cartridges, subplate mounting, etc.

Read more
Top